Category Archives: Blog

Pauls Plumbing   →  Blog   →  Blog
Categories Blog Posted on

Bathroom Renovation By Paul’s Plumbing.

Bathroom Renovation Process with Paul 0406 071 659


Paul and his team start by completely dismantling the bathroom down to its wooden frame, making sure to remove each sheet with great care.

Paul and his team then proceed to jackhammer the old flooring and remove it completely.

This enables us to thoroughly evaluate any areas that require fixing before proceeding with wall sheathing.

Plumbers

After finishing these tasks, Paul's Plumbing initiates the rough in process with their plumbers

which includes installing new hot and cold water pipe using auspex piping also installation shower mixers, bath mixers as well as water outlets for vanity units while simultaneously addressing all drainage issues within this stripped-down state of the bathroom. Paul and his team only use parts from Reece or Tradelink

Electricians

Our electricians enter the picture once plumbing work behind walls is complete, allowing them to smoothly perform their required job duties while maintaining safety standards and avoiding interference with other contractors' efforts during bathroom renovations.


After confirming everything at an initial level, one critical aspect that requires attention is the installation process Sheet your renovated bathroom using 6mm villa board sheeting only after confirming that all work has met requisite standards.

Water Proofing stage


Next, the waterproofing process will start. Once the bathroom is properly sheeted, we move on to the critical step of waterproofing.

In this process, we ensure the entire bathroom is waterproofed carefully and efficiently to prevent any potential water damage that may occur in the future

After completing the waterproofing, we begin the important task of beading.

Beading involves creating a proper slope on the floor so that water can drain into the floor waste. Our team achieves this by using sand and cement to bed the floor at a depth of around 40mm. This creates the correct fall to ensure optimal drainage and prevents any future water damage or mold growth.

Tiling stage

After carefully choosing your colors, our tiler meticulously installs tiles that stretch from floor to ceiling.

We offer two options - 400x400 and 300x600 tiles - to cater to your specific requirements.
Every tile installation is meticulously siliconed around the wall and base to ensure longevity and durability.

Apart from guaranteeing full water resistance, this measure also secures your investment against any potential water harm due to regular usage.

Fit off Plumber

In your bathroom, the plumber will carefully connect all fixtures such as your wall mounted vanity unit, back to wall toilet installation, shower wall mixer, elegant towel rail, and sleek mirrors.

The electrician will meticulously set up all of your power points and light switches after this installation process is complete.

Shower Screen Stage

Both professionals involved in this renovation project must complete these crucial steps seamlessly before moving on to the next phase, which entails putting up a beautiful shower screen that enhances the overall aesthetic appeal of your bathroom.

Final stage

At the end of this process, we thoroughly clean your brand-new bathroom so it shines like a diamond! Our team carries out each step of the process with precision and care to deliver a stunning new bathroom that exceeds your expectations.

Call Paul on 0406 071 659 if you're thinking about a new bathroom

Categories Blog Posted on

Are Hot Water Systems Covered by Insurance?

Homeowners need to know what their insurance covers in order to protect their home and belongings. One important factor is whether or not a hot water system is covered by insurance.

leaking hot water system from Ht55 and h50

Leaking hot water system from the HT55 valve and H50 can be a major problem in any home. It is important to identify the source of the water leak and take steps to fix it, as leaks can cause a lot of damage if left unchecked. The HT55 valve and H50 are common parts on water heater, so it is important to understand how these components work and what could be causing a leak before attempting repairs.
The HT55 valve is responsible for relieve excess pressure caused by water expansion of the your water unit , while the H50 allow cold water to be relieved during the heating expansion cycle. of your hot water system. If either component malfunctions or wears out over time, then it can lead to an increase in pressure that may result in your tank leaking. Other potential causes include corrosion on the pipes or valves due to age or improper maintenance, as well as frozen pipes during cold weather months and ht55 and h50 should be replaced every 5 years and will not be covered by home insurance.

Hot water unit anodes

Hot water service with sacrificial anodes are becoming increasingly common in households. If you have one, it is important to understand the importance of replacing the sacrificial anode every five years. Doing so will help extend the life of your tank and save you from costly repairs or replacement.

Sacrificial anodes should be replaced every five years as part of routine maintenance to prevent leaking hot water systems. Checking your hot water tank regularly will prevent any major problems from occurring. Unless specifically stated in your insurance policy, these types of maintenance costs may not be covered, so check before making any major repairs!

Heating elements

If you own a hot water system, you may be concerned about the potential for damage caused by faulty hot water elements. In particular, the bolts that hold the element in place can rust out over time and cause hot water it to drip onto electrical wiring. This can lead to an electrical trip, resulting in costly repairs or hot water installation. It is imperative to make sure that your home's appliances and utilities are covered by comprehensive insurance in case of damage caused by owner maintenance. Find out what kind of coverage your insurer offers for hot water units. Mechanical breakdowns and other common problems, like excessive corrosion or rusting, are covered in most policies.

Hot water unit tempering valve

Hot water tempering valve are an important part of the home, and when they fail, it can be an inconvenience. When a water heater tempering valve fails, it means that no hot water will be available to the home. Homeowners may be wondering what a tempering valve replacement would cost Replacing tempering valve and hiring a hot plumber will not be covered under their home insurance policy.

The answer is that coverage varies depending on the type of policy taken out and its provisions. Generally, most homeowners insurance policies do not provide coverage for routine maintenance or repairs on replacing tempering valve however some may cover particular parts or components of a tank if they are damaged due to an unforeseen event such as vandalism or fire damage or flood The best way for homeowners to determine what type of coverage is included in their policy is to consult with their insurer directly.

Water heater leaking from base

As a homeowner, it's important to understand the coverage limits of your homeowners insurance policy. If your tank is leaking from both the top and bottom due to old age, you may be wondering if it will be covered under home insurance and whether the plumbing costs associated with repairing or replacing it will be taken care of as well.

The answer largely depends on your specific policy terms, but generally speaking most standard home insurance policies do not cover wear-and-tear caused by aging appliances such as hot water units. However, some insurers may offer additional coverage for these types of scenarios.

Hot water unit replacement

A standard homeowner's policy provides peace of mind that any costs associated with replacing a hot water unit in the event of an unexpected incident will be covered. Before making any repairs, homeowners should contact their insurer to find out exactly what their policy covers and how much compensation they can expect.

If you require any more information please contact Pauls Plumbing on 0406 071 659 or email us at paulsplumbinggroup@outlook.com

Categories Blog Posted on

Water Hammer Brisbane Ipswich and logan

"Find Solutions to Fix Water Hammer in Brisbane Ipswich & logan!"

Water hammer is a common issue that occurs in water pipes in homes throughout Brisbane and Ipswich and logan. It is characterized by a loud banging or knocking sound, which can be disruptive and annoying. Understanding what causes it can help you take measures to prevent it from occurring in your home.

Paul’s Plumbing been providing plumbing services for years in Brisbane, Ipswich and logan area and they know all about water hammer. The most common cause of this phenomenon is an abrupt change in the velocity of the flowing water, such as when a valve closes suddenly or too quickly after being opened. Other possible causes include air pockets that develop inside the pipes due to pressure changes, high-velocity turbulence inside the pipe system, and incorrect installation of valves or fixtures or tap washer jumping up and down. Loose cooper pipe in the wall that have been incorrectly installed or clips that have broken due to old age washing machine and dishwasher shutting fast.

Discover what causes water hammer.

Are you experiencing water hammer in your Brisbane, Ipswich and logan home? Water hammer is a common plumbing problem where you hear loud banging or knocking coming from your pipes.

Generally, water hammer occurs in high pressure (e.g., mains pressure) water systems either when a tap is turned off abruptly or by fast-acting solenoid valves that suddenly stop water flow through the pipes, creating a shock wave that causes the pipes to vibrate and shudder.

Can water hammer cause damage?

Having a water hammer problem can cause erosion, damage to pipes, valves, and fittings, and even burst pipes as a result of the water hammer problem. In the modern plumbing system, chambers of air are used to absorb the shock of water hammer to reduce damage caused by water hammer.

Don't let water hammer ruin your hot water system! Learn how to identify and prevent water hammer issues

Water hammer could be coming from your hot water system as the older hot water system have duo valves that have tap washer. By replacing the old-style duo valve on your hot water system with a new 1/4 turn ceramic disc type, you'll be able to prevent water hammer from ever becoming an issue again.

If your old hot water system needs a new duo valve or a service, look no further than Paul's Plumbing! We are experts at servicing and installing any kind of hot water system.

Don't wait until it's too late - contact us now for our top-quality hot water plumber! Let us take care of everything so you don't have to worry about a thing - we promise fast service and a smooth installation process Call Paul on 0406 071 659

Learn about the causes and solutions of water hammer caused by a tap washer!

Water hammer could be coming from your taps by replacing the tap washers in your taps is one of the easiest and cost-effective ways to stop water hammer. This should be done every few years to ensure they remain in good condition.

Water hammer caused by your water meter.

Are you hearing a mysterious water hammering noise coming from the front of your house? It could be caused by your old stop cocks in your water meter that are due for replacement. Paul's Plumber in Brisbane, Ipswich is here to help diagnose and solve your issues. or a simple call to Queensland Urban Utilities to replace your water meter stop cock.

The sound of a water hammer happens when the valve in the plumbing system closes too quickly, which causes tiny shocks throughout the pipes. This can cause damage to your pipes over time if it isn't taken care of properly. Luckily, Paul's Plumber has decades of experience in diagnosing and solving these issues!

Are you hearing a hammer-like sound coming from your pipes?

Pauls Plumbing in Brisbane Ipswich and logan is here to help you solve a common plumbing issue known as water hammer. Have you ever heard a loud banging sound coming from your pipes? This could be caused by an old clip in the wall or roof, and it can cause your pipe to bang around. Fortunately, Pauls Plumbing has the experience and know-how to fix this problem for you!

The team of plumbers at Pauls Plumbing can replace the old clips with new ones, ensuring that your pipes are held firmly in place. They also check for any damage to the silicone between your pipe and wood – replacing it if necessary – so that there are no leaks or other issues. Don’t let water hammer ruin your day – give Pauls Plumbing a call today on 0406 071 659 for fast and reliable service.

Discover if water hammer arrestors really work!

Are you looking for an answer to the question of whether water hammer arrestors work? Paul's Plumbing in Brisbane and Ipswich can help! Water hammer arrestors are a great way to prevent damage caused by rapid changes in water pressure, making them essential for any home. Installing these devices is easy, as they simply attach to your existing plumbing system with no major modifications required. Plus, they're very affordable - costing just a few hundred dollars - so that you don't have to break the bank on plumbing repairs.

Water hammer arrestors are small but powerful devices designed to absorb shocks from sudden pressure changes caused by stopping or starting an appliance such as a washing machine or dishwasher. They can be installed anywhere along your piping system, usually near the point where water enters the house or after fixtures such as washing machines or dishwashers.

If you've been hearing loud, banging noises from your pipes recently, it could be water hammer. A water hammer arrestor is the best way to reduce the noise and ensure that your plumbing system is functioning properly. If you live in Brisbane or Ipswich, Paul's Plumbing has an experienced team of plumbers who can help you with installation and repair of water hammer arrestors.

Water hammer arrestors: when should they be used?

When fast closing shutoff valves, dishwashers, and clothes washers suddenly stop the flow of water in a piping system, water hammer arrestors absorb the shock.

How water hammer arrestor work

Water Hammer Arrestor works by compressing air in order to absorb the induced pressure wave. The arrestor is placed at an angle of 90° to the water flow, just upstream from the offending device. As soon as the device closes, the pressure wave moves back along the pipe.

Where to buy water hammer arrestors?

If you're looking for the best place to buy a hammer arrestor from, then look no further! Reece Plumbing Tradelink Cooks plumbing and bunnings are great places to get your hands on the most reliable and high-quality hammer arrestors. Not only will they have an unparalleled selection of products, but their experienced staff can help you find exactly what you need for your project.

At Reece Plumbing, you'll find a variety of hammer arrestors in different sizes and shapes to suit any job you may be working on. They also offer competitive prices so that everyone can afford the best quality tools. Their staff is incredibly friendly and knowledgeable too, so don't hesitate to ask them questions if you're unsure which product is right for your specific needs.

Purpose of a water hammer arrestor

The purpose of a water hammer arrestor is to reduce the pressure surge created by sudden changes in the flow of liquid through a pipe. When installed correctly, they work to minimize noise levels and help protect your plumbing system from damage caused by high pressure surges.

Paul's Plumbing can professionally install water hammer arrestors for an affordable cost.

If you are experiencing water hammer in your home and don't know what to do? Don't worry, Paul's Plumbing has got you covered! We are the leading plumbing services provider for Brisbane, Ipswich and Logan. We offer reliable and trust-worthy services that will make sure all your needs are taken care of! Our specialists have over 18 years of combined experience taking on any kind of plumbing job. Whether it be a leaky hot water system or a blocked drain or major water hammer issue, we can help you out. Don't hesitate to call Paul today on 0406 071 659.  With our top-notch services, there is no need to look anywhere else. Get in touch with Paul's Plumbing now and let us take care of all your plumbing woes!

 

Categories Blog, Uncategorized Posted on

Why You Should service your hot water system in Brisbane Ipswich & Logan

Hot Water system Brisbane and Ipswich

Hot water service in Brisbane is a must for any home or office. There are many benefits of having a hot water service in Brisbane and Ipswich .

Here are some of the reasons why you should get a hot water service in Brisbane:

  1. Hot water service in Brisbane can save you money on your energy bills.
  2. Hot water tank service in Brisbane can improve the quality of your life.

The Importance of Hot Water Service in Brisbane for Your Quality of Life

We provide hot water hire systems for Brisbane and Ipswich, as well as hot water heater plumbers near me for emergency plumbing services. There are actually many more benefits to having a reliable hot water system than just being able to take a shower. Here are just a few reasons you should ensure your hot water system is working properly: Improved health and hygiene - Hot water can improve your health and hygiene, which is one of its main benefits. Hot water kills bacteria and viruses that can cause illness, so a functional hot water system is especially critical if you have young children. Warm or hot showers can ease the symptoms of skin conditions like eczema, psoriasis or acne. Relaxation and stress relief - You can also take hot showers as a way to relax after a long day at work or after an event that is stressful. It has also been shown that being in warm water can improve your mood and reduce anxiety levels Pain relief - The heat from the water helps to increase blood flow, which can ease aches and pains, especially arthritis pain.

hot water

Hot Water plumber Service in Brisbane and Ipswich

Need a Plumber repairman hot water heater replace, plumber hot water heater prices, hot water repairs ,hot water repair cost Hot Water Service in Brisbane and Ipswich – A Comprehensive Guide The Relationship Between Hot Water Service in Brisbane and Ipswich Your Health Why is it important to have a hot water service in Brisbane? What are the benefits of having a hot water service in Brisbane and Ipswich ? How can a hot water service in Brisbane and Ipswich improve your health? What are some things to consider when choosing a hot water service provider in Brisbane?

How to Get the Best Service in Brisbane and Ipswich

,hot water heater repairman, hot water heater man near me, Electric hot water heater repair Brisbane ,water heater service Logan

The Different Types of Hot Water tanks

A hot water heater repairman near me who can fix different types of hot water systems is critical.
 In Brisbane, electric hot water tanks are most common. Here's a guide to help you decide.
 Water is heated when needed using electric hot water storage systems. In small homes, instantaneous or demand-type systems are used to heat water without storing it.
Solar water heating systems reduce your carbon footprint and energy costs. The electric heat pump transfers heat like an air conditioner. The systems use resistance heating instead of electric hot water and are more efficient. Consult with a licensed hot water plumber before installing a brand-new hot water system so they can assess your needs.

FAQs About Hot heaters Service in Brisbane

Need a Plumber to install a hot water heater installation near me or a plumbing emergency hot water that is leaking water Paul Plumbing has hot water plumbing near me, If you nee a plumber to install hot water heater call Paul 0406 071 659

If you are thinking about getting a hot water service in Brisbane, there are many good reasons to do so Hot water services can save you money on your energy bills, provide you with hot water on demand, and give you the peace of mind that comes with knowing your hot water system is reliable When it comes to choosing a hot water service in Brisbane, there are a few things to keep in mind You will need to decide what type of system is best for your home, as well as find a reputable company to install and maintain your system With a little bit of research, you can find the perfect hot water solution for your home.

Need a leaking hot water plumber call Paul's plumbing 0406 071 659

pipe-406906_1920
Categories Blog Posted on

Why your drain is blocked

Tree Roots

The most common reason why people get blocked drains is because of tree roots. Living in such a beautiful, leafy, green city has its downside. Tree roots can enter a pipe many different ways but the most common is through a crack in the pipe. Cracks in pipes are caused by ground movement, material fault, poor installation or by large tree roots putting pressure on the pipe. Earthenware pipes (clay pipes) are very common in the older suburbs of Brisbane. This type of pipe is quite hard and brittle and will crack easily. It also is sealed using a rubber gasket which degrades over time also allowing tree roots to enter. Many houses built before the 1980s will have earthenware pipes below the ground. Over the year’s tree roots enter these cracks, often making the cracks even larger allowing more roots to enter the drains. Hydro jetting unblocks the drain quickly and removes the tree roots from the full internal bore of the pipe.

Collapsed or Damaged Pipes

Pipes can also be damaged or collapsed over time. Damaged pipes can be caused by construction processes, heavy equipment driving above, severe ground movement and many other possibilities. When this happens, we can identify the problem using our camera inspection equipment. A high definition recording of the damage can be supplied to you via USB should you require it. Using our radio frequency locator, we can accurately locate the issue and even determine the depth. Old, deteriorated pipes are very common in older areas of the city, often even when there are no tree roots to promote more extensive cracking.

Grease

In restaurants, commercial kitchens and even at home, grease builds up in drains leaving only a small aperture for the waste to pass through. Commercial kitchens often drain to a grease trap which catches the grease before entering the council sewer. These grease traps require pumping out at regular intervals however the pipes that drain in to them are often left unchecked. Hydro jetting will dislodge the grease and flush it through. We use a grease dissolving product called grease blaster which prevents grease sticking to the pipe further down after it is flushed out. This prevents similar issues from reoccurring in the future.

Sand, Silt and other Debrisblockedpipe

Sand and silt can often enter pipes particularly storm-water drains. A hydrojetter easily flushes the sand through and unblocks the pipe. Concrete occasionally enters drains during construction work however it is a simple process to remove using a hydrojetter. Other debris can have a similar clogging effect when stuck in pipes. As junk gets caught in the pipe and builds up over time, it can cause nasty problems with blocking other things from draining away and build up to further issues. Click to call 
11
Categories Blog Posted on

Choosing the Right Toilet

Choosing the right toilet can be a challenge and more often than not usually ends up in numerous trips to the DIY store and a waste of your own time and money. If you follow this guide below you can save the hassle by picking the right toilet suite to suit your home and its existing infrastructure.

Types of toilet available:

Back to Wall Toilet Suites

Back-to-Wall-Toilet-SuitesBack to wall toilet suites sits flush against your bathroom wall. This means that there are no gaps between the wall and toilet at all. This type of toilet is very modern in design suiting contemporary style bathrooms. As back to wall suites have no gaps they are also easier to clean.

What you need to know before installing a back to wall toilet suites

Toilet Pan Set out:

Measure from the wall to the center of waste where the toilet goes into the ground this will usually be in range from 120mm-200mm.

Water Inlet for toilet cistern

Now you have made your mind up on the toilet you need to make sure you have the right water entry point most toilets have a bottom water entry point with a mini cistern cock on the wall. The modern back to wall suite have a rear or back entry water point that is concealed at cistern height. This position is very particular to the make and model of suite and will very between brands.

Floor Level

The modern back to wall suite unfortunately has one weakness in its installation versatility and that is that it’s not able to be installed in positions with medium/large fall. If your floor falls away noticeably to a floor grate unfortunately a back to wall suite in not going to be flexible enough to fit in this circumstance. Skirting tiles When installing a back to wall suite in most circumstances if the walls are not tiled above the level of the toilet suite than the skirting tiles will need to be removed so that the pan can go back flush against the wall. A tiler or handy man will be required to cut and replace the tiles removed for installation at an extra cost.

Skirting tiles

When installing a back to wall suite in most circumstances if the walls are not tiled above the level of the toilet suite than the skirting tiles will need to be removed so that the pan can go back flush against the wall. A tiler or handy man will be required to cut and replace the tiles removed for installation at an extra cost.

Close Couple Suites

Caroma-profile-4-$820-installedClose Couple suites have the toilet pan and cistern joined so you cannot see the flush pipe. This type of toilet will suit all types of bathrooms and is very traditional.

What you need to know before installing a Close Couple Suites wall toilet suites

Toilet Pan Set out:

Measure from the wall to the center of waste where the toilet goes into the ground this will usually be in range from 120mm-200mm

Water Inlet for toilet cistern

Now you have made your mind up on the toilet you need to make sure you have the right water entry point most toilets have a bottom water entry point with a mini cistern cock on the wall. The modern back to wall suite have a rear or back entry water point that is concealed at cistern height. This position is very particular to the make and model of suite and will very between brands.

Connector Suites

Connector-SuitesConnector suites are the most traditional types of toilets with the cistern joined to the pan by as plastic flush pipe and connector plate. This type of toilet allows for the greatest level of flexibility during installation.

Types of Pans

S-trap Toilet Pans

S-trap Toilet Pans are the most commonplace in Australia. It is identified with the toilet waste of the trap connecting directly into the floor-mounted pan collar.

P-trap Toilet Pans

P-trap version pans have horizontal outlet waste which connects into a pan collar mounted on the wall.

Skew trap toilet pans

Skew trap version pans are available in left and right hand models with a horizontal or angled outlet waste which is offset at 90° and connects directly into a pan collar mounted on a side wall. Sometimes this is not visible due to the pan style and design if this is the case then a safe rule of thumb is if you currently have a close coupled or back to wall toilet suite than the same style of suite will be versatile enough to fit.
hot-water
Categories Blog Posted on

Facts about Hot Water Systems

Keeping your energy bills down is really important. There are many things you can do to help. For example:
  • Electric hot water system on full tariff can be expensive to run. You may be able to switch lower cost “off peak” tariff. Check with your energy provider or ask your electrician / installer about options available to you.
  • High efficiency, solar and heat pump water heaters can be a lower running cost alternative, particularly compared to an electric water heater on continuous tariff or an older.
  • Temperature Pressure Relief Valve can be found on storage models only. It is always near the top of the water heater, at the same level as the hot water outlet.
By gently lifting the Hot water system Ht55 lever up, you can release this valve every 6 months, so your water heater runs safely. During each heating period, the hot water valve releases a bit of water through the drain line. When the Electric hot water system heats the water, it expands by 1/50 of its volume. Continuous leakage of water from the hot water valve and its drain line may indicate a problem with the water heater. Temperature pressure relief valves and cold water relief valves should be replaced every 5 years, according to the manufacturer.

Our industry associations

master plumbers - Bathroom Renovation By Paul's Plumbing.Website logo new large - Bathroom Renovation By Paul's Plumbing.

Contact Us

This field is for validation purposes and should be left unchanged.
Copyright All Rights Reserved © Paul's Plumbing

    Contact Us

    Thanks for choosing Paul's Plumbing for your plumbing needs.
    Please fill our short form and one of our friendly team members will contact you back.